ETW,ETW国际,上海ETW,ETW International,China ETW,ETW Manufacturer,Mining Truck TR60

Lista de productos

Mining Truck TR60

Technical Parameter of Mining Truck
N.V.W.:	40000kg
Payload:	55000kg
G.V.W.:	95000kg
Overall dimensions (LWH):	913044504440mm
Wheel bass:	4170mm
Track:	Front : 3320mm Rear 2900mm
Max Speed	57.5km/h
FRAME
Full box section frame rails, integral front bumper, closed-loop crossmember and torque tubes of 290 MPa yield strength steel. Crossmember connections are 655 MPa steel castings.
Engine
Model	Cummins QSK19-C650
Type	6-cylinder, in-line, 4 Cycle, Turbocharged/ After cooler
Rated power	485 kW (650 hp)
Maximum Torque	3085 Nm@1300rpm
Bore x Stroke	159 x 159 mm
Displacement.	18.9 liters
24 volt negative ground electrical system. Two 12 volt 165Ah batteries with master disconnect switch. 8.9KW starter. Neutral start. 70A alternator with integral voltage regulator.
TRANSMISSION
Allison M6610AR automatic electronic control with Soft Shift feature. Planetary gearing with six speeds forward and two reverse. Integral TC 682 torque converter with automatic lock-up in all speed ranges. Hydraulic Retarder. With body up, gear range is limited to 1st forward.
Drive ratio: Forward Gears 1	4.00
Drive ratio: Forward Gears 2	2.68
Drive ratio: Forward Gears 3	2.01
Drive ratio: Forward Gears 4	1.35
Drive ratio: Forward Gears 5	1.00
Drive ratio: Forward Gears 6	0.67
Drive ratio: Reverse Gear1	5.15
Drive ratio: reverse Gears 2	3.46
DRIVE AXLE
TEREX heavy duty axle with full floating axle shafts, single reduction spiral bevel gear differential, and planetary reduction at each wheel.
Differential ration	3.73:1
Planetary ration	5.80:1
Total Reduction ration	21.63:1
Suspension
Front: TEREX manufactured kingpin strut-type independent front wheel suspension using self-contained, variable rate, nitrogen/oil cylinders. Rear: TEREX variable rate nitrogen/oil cylinders with frame linkage and lateral stabilizer bar.
Maximum Strut Stroke (Front).	251 mm
Maximum Strut Stroke (Rear).	182 mm
Maximum Rear Axle Oscillation	6.5°
Tyres
Type	Front and Rear 24.00-35(36PR)
Rim Width	17in
BRAKES
SERVICE: All hydraulic brake system control. Transmission mounted pressure compensating piston pump provides hydraulic pressure for brakes and steering. Independent circuits front and rear. Each circuit incorporates a nitrogen/hydraulic accumulator which stores energy to provide instant braking response. PARKING Rear brakes: applied by spring loaded opposing piston on disc pack, hydraulically released. RETARDATION–Modulated lever control of rear disc brakes or hydraulic retarder in transmission. 670 kW (900 hp) continuous retardation. SECONDARY: Park push button solenoid control applies service and parking brakes. Automatically applies when engine is switched off. Parking brake applies when system pressure fails below a predetermined level.
Front Brakes	Dry Disc
Disc diameter.	710 mm
Pad area, total	1394cm²
Rear Brakes	TEREX oil cooled, multiple disc, completely sealed from dirt and water.
Braking Surface, total.	47151 cm²
STEERING
Independent hydrostatic steering with closed-centre steering valve, accumulator and pressure compensating piston pump. Accumulator provides uniform steering regardless of engine speed. In the event of loss of engine power it provides steering of approximately two lock-to-lock turns. A low pressure warning light indicates should the system pressure fall below 83 bar (1200 lbf/in2). Steering conforms to ISO 5010,SAE J53.
Maximum Tyre Steering Angle	39°
HOIST
Two body hoists mounted inside the frame rails. Hoists are two-stage with power down in the second stage. The body hydraulic system is independent of the steering hydraulic system.
System Pressure	190 bar
Body Hydraulic Pump Flow Rate @ 2 100 rpm	227 liter/ min
Body Raise Time	16 Seconds
Body Lower Time	14 Seconds
BODY
Longitudinal \'V\' type floor with integral transverse box-section stiffeners. The body is exhaust heated and rests on resilient impact absorption pads. Full time exhaust is optional. Body floor wear surfaces are high hardness(450 BHN) abrasion resistant steel, of yield strength 1200MPa All other wear surfaces are high hardness (360-440BHN) abrasion resistant steel, of yield strength 1000 MPa
Floor thickness	19 mm
Side thickness	10mm
Front thickness, lower	10mm
Stuck volume	. 26 m³
Heaped volume	35 m³

Comentarios

Otros productos

Concrete Mixing Plant Concrete Mixing Plant Introduction of Concrete Mixing Plant 1. HZS series concrete plant is newly-developed on the basis of SINOWAY\'s

Truck Crane QY30K5 Main Features of Truck Crane 1. Machine appearance: harmony, smooth and nice. 2. Self-made special truck crane chassis: with strong-power a

Truck Crane QY50K Main Features of Truck Crane 1. 6 designs of this product have won China state patents. 2. Full-width driver\'s cab brings brightness a

Bulldozer Bulldozer A bulldozer is a heavy piece of earthmoving equipment. It uses a front-mounted dozer blade to push soil forward and create a level s

Wheel Excavator, Wheel Digger SWEL80 Specifications of Wheel Excavator, Wheel Digger Weight Operating Weight 80.2t Bucket Capacity Standard Bucket Capacity 0.35M3